quality lathe work

General Landrover stuff, greenlane trips, shows, journeys, stories, etc.
Post Reply
Moogling
In overdrive
Posts: 288
Joined: Sat Oct 20, 2012 10:35 am

quality lathe work

Postby Moogling » Wed Feb 05, 2014 8:15 pm

Some of the last bits for Ellie (my IIB) turned up today

Wheel studs for holding the step on - with the earlier type thread (double sided nuts)

Image

A bit of a plug for Abtech Engineering who did this work for me!
lanceley
Running on six!
Posts: 142
Joined: Sat Apr 13, 2013 11:33 am

Re: quality lathe work

Postby lanceley » Wed Feb 05, 2014 9:30 pm

Almost too pretty to use a mere wheel nuts.....
Moogling
In overdrive
Posts: 288
Joined: Sat Oct 20, 2012 10:35 am

Re: quality lathe work

Postby Moogling » Wed Feb 05, 2014 10:16 pm

Agreed!
DasLandRoverMan
The 1-Ton Welder
Posts: 1334
Joined: Sat Oct 20, 2012 9:33 am
Location: West Lakes
Contact:
Contact DasLandRoverMan

Re: quality lathe work

Postby DasLandRoverMan » Wed Feb 05, 2014 10:50 pm

You're bringing sexy back...
Westlakes All Wheel Drive

Carpe Dentum - Sieze the Teeth!!!
User avatar
Wheeledbeast
In overdrive
Posts: 1360
Joined: Mon Apr 15, 2013 1:41 pm

Re: quality lathe work

Postby Wheeledbeast » Thu Feb 06, 2014 4:24 pm

:shock: Oooooooh Shiney :!: …..

Are they stainless or just polished up :?:
Moogling
In overdrive
Posts: 288
Joined: Sat Oct 20, 2012 10:35 am

Re: quality lathe work

Postby Moogling » Thu Feb 06, 2014 7:14 pm

just mild, not polished at all as far as I can tell, but clean :)

very pleased! I asked for 6 and they gave me 8
User avatar
parksy64
Running on six!
Posts: 267
Joined: Sun Jan 06, 2013 8:00 am
Location: Wiltshire

Re: quality lathe work

Postby parksy64 » Thu Feb 06, 2014 7:57 pm

Nice!
eastern101
Low Range
Posts: 8
Joined: Sat Jan 25, 2014 9:08 am

Re: quality lathe work

Postby eastern101 » Wed Feb 12, 2014 11:52 pm

Nice I'm now possibly getting some made up for my 101 deeper ones to bring step out further in deeper offset rims.
MikeD
Petrol sniffer
Posts: 29
Joined: Sat Jan 25, 2014 7:52 am

Re: quality lathe work

Postby MikeD » Thu Aug 07, 2014 9:37 pm

Hi moogling,
I know this is an old thread, but i'm looking to get some extended nuts made up myself, do you mind if i ask how much (roughly) you paid to get them done? Just so i know if i'm being seen off...
Thanks
Mike
Moogling
In overdrive
Posts: 288
Joined: Sat Oct 20, 2012 10:35 am

Re: quality lathe work

Postby Moogling » Fri Aug 08, 2014 6:35 pm

I paid £100 to a local chap who does work for my mothers company. I don't know if that was expensive or cheap, but I was happy.
Post Reply

Return to “General Discussion”

Who is online

Users browsing this forum: No registered users and 11 guests